Instruction ManualULTRA-MICROLength: 6.75 in (171mm)Height: 2.8 in (71mm)Main Rotor Diameter: 6.6 in (167mm)Weight with Baery: 1.0 oz (28
10• When transporng or temporarily storing the baery, the temperature range should be from approximately 40–100°F. Do not store the baery or model
11To charge the ight baery, plug the included charge cord into the rear of the transmier. Plug the baery into the other end of the charge cord. Th
12Transmitter DetailsThe Nanos FP 75 includes a 5-channel Helicopter Transmier with 2.4GHz technology, stability mode and digital trims.Flight Mode
13HIGH rate mode. To toggle the dual rate seng, unplug the helicopter and turn o the transmier. Then, power on the transmier and plug th
14Flight ControlsIn the event you are not familiar with the controls of the Nanos FP 75 please take the me to familiarize yourself with them as follo
15Sck UpForward FlightSck DownBackward FlightSck Le Rolls LeSck Right Rolls RightThe right-hand sck controls both the elevator (pitch for
16Installing Flight BatteryRemove the canopy from the helicopter and install the fully charged ight baery on the hook-and-loop holder with the baer
17InitializationTo inialize the helicopter, rst power on the transmier and then plug in the baery, replace the canopy, and place the helicopter on
183-Axis ModeAs your skills advance, you may wish to transion to 3-axis mode, which provides more maneuverable ight but is not stabilized and is the
19Further, the cyclic trim buons have no eect in 3-axis mode. If correcons are required in this mode, they should be made mechanically by changing
2Table of ContentsIntroducon ������������������������������������������������������������������� 3Safety Precauons ���������������������������������
20If the helicopter tends to consistently roll or pitch in a parcular direcon in 3-axis mode, it may be necessary to mechanically trim the helicopte
21the same amount by twisng the plasc pieces clockwise the same number of turns.If the helicopter tends to pitch backward, the servo pushrods should
22Aer you’ve properly trimmed the helicopter and become familiar with its handling and capabiliesyou may be able to y in other smaller and less ope
23Flying (General)Now that you’ve selected a suitable ying area you’re ready to y! And when making your rst ights we suggest following these steps
24• While aempng to establish a low-level hover out of ground eect (approximately 20–24 inches high or higher) you can check to see if any trim adj
25inputs as minimal as possible to prevent over-controlling the helicopter�• Connue to pracce unl you’re comfortable hovering the helicopter at app
26Tx/Rx Binding/LinkingBinding/linking is the process of programming the receiver to recognize the Globally Unique Idener (GUID) code of a single sp
27Warranty, Support & Service30-Day Limited Warranty Term Period:We warranty that the Product(s) purchased (the “Product”) will be free from defe
28will be returned to you at your expense.If you purchased your Product from a HobbyTown Internet site not aliated with a local store, please consult
29 Ref # Item # Descripon AZSH2200 Nanos FP 75 RTF Micro Heli AZSH2206 Main Board: Nanos FP 75 AZSH2207L Le Servo: Nanos FP 75 AZSH2207R Right
3IntroductionWhether you’re looking to advance from your rst CX heli or quad, or you're an experienced heli pilot looking for some ying fun aro
30Exploded View
31
32www.Ares-RC.com© 2014
4Safety PrecautionsKeep items that could become entangled in the rotor blades away from the rotor blades, including loose clothing, to
5• Never operate your model if the voltage of the baeries in the transmier is too low.• Always operate your model in an open area away from obstac
6FCC InformationThis device complies with part 15 of the FCC rules. Operaon is subject to the following two condions:(1) This device may not cause h
7Needed to CompleteThe Nanos FP 75 RTF includes everything needed to y right out of the box. There’s nothing extra to buy or provide!
8Flight ChecklistPLEASE NOTE: This checklist is NOT intended to replace the content included in this instruconmanual. Although it can be used as a qu
9• You must charge the LiPo baery in a safe area away from ammable materials. • Never charge the LiPo baery unaended at any me. When charging the
Comentários a estes Manuais